Garage Door Spring Installation

A1 Garage Door Service » ARTICLES » Garage Door Spring Installation

GARAGE DOOR SPRING INSTALLATION

Springs of garage doors are vital components that counterbalance the weight of the garage door, making it easy to open and close manually or with the assistance of a garage door opener. Replacing or installing garage door springs is a task that requires precision and knowledge of the tensioning process. Springs have a limited timespan, typically measured in cycles. The average lifespan of garage door springs is around 10,000 cycles , but this can vary based on usage and maintenance.

The garage door spring installation is a task that requires meticulous attention to detail and respect to safety precautions. While some homeowners may opt to handle this as a do-it-yourself project, it’s vital to remember that handling springs incorrectly can result in significant harm. If you are hesitant or uncomfortable with the process, it is strongly advised that you seek the assistance of a professional garage door specialist. Garage door springs that are properly installed and maintained contribute to the smooth and effective operation of your garage door, ensuring its lifetime and safe use for years to come.

High-quality garage door springs help your garage door achieve its peak performance. These springs are under extremely high tension to raise and lower your garage door. Take note that garage doors are heavy. Thus, they need the force from the springs to open and close. Heavy-duty springs can open and close up to 10,000 cycles. However, they can also suffer aging and wear-and-tear. You must regularly maintain your garage door springs to guarantee your garage door’s function. If you encounter any problem, don’t hesitate to contact A1 Garage Door Pittsburgh. We provide the highest quality garage door repair in Pittsburgh. Our highly qualified technicians have undergone proper training and years of experience to become the best in the area. Contact us anytime for your 24/7 emergency garage door needs.

When Should You Install a Garage Door Spring?

Garage door springs have cycles of up to 10,000. This means they can open and close your garage door up to 10,000 times. However, your torsion springs may wear out as they approach that number. Your springs may even deteriorate quicker if it’s made of low-quality materials, installed improperly, or unmaintained. If you think your garage door springs are about to snap, contact your technician for a garage door spring installation. Garage door springs are extremely dangerous to handle, especially when they’ve snapped. Hence, you shouldn’t attempt to go near your door or use it. You must replace your springs immediately to avoid accidents and damages to your valuables.

How to Install a New Garage Door Spring

Garage door spring replacement is a dangerous job. Experienced and certified garage door specialists should only handle this task. If you don’t have what it takes to safely and correctly install torsion springs, you better leave the job to professionals. Here’s a step-by-step guide to new garage door spring installation.

Safety first: use a C-clamp to lock the garage door in its position and prevent it from hurling upwards and injuring you.

Insert a winding bar into one hole of the winding cone of the intact garage door spring, not the broken one.

You will use this to loosen the two setscrews on the winding cone.

Insert a second winding bar at a 90-degree angle and start unwinding the spring.

Lose the nuts and bolts on the center bracket to disconnect the stationary spring cones.

You should be able to slide the springs toward the other end after.

Secure the torsion tube on the center bracket with a C-clamp or locking pliers.

Loosen the setscrews on both sides of the lift cable drum to disengage the cables.

Remove the cable drum by sliding the torsion tube to the other side.

Next, slide the broken spring out.

You must have the perfect garage door spring replacement to install.

Thus, you must measure the old spring and purchase the new torsion springs. Use a tape measure to determine the spring wire diameter and inner spring diameter and length. Determine the wind direction as well.

Insert the new spring onto the torsion tube.

The stationary cone should be facing the center bracket.

Insert the cable drum with the lift cable, the torsion bar, and the center bearing.

Do this for both the springs and attach the two stationary cones to the center bracket.

Replace the rollers, brackets, and cables if necessary.

Adjust the tension of the cables and torsion springs as well.

High-Quality Garage Door Springs in Pittsburgh

A1 Garage Door Pittsburgh offers reliable garage door springs for residential and commercial garages in Pittsburgh. Our springs are made of high-quality and durable steel with cycles of up to 10,000. This means your garage door can last up to at least ten years without any performance issues. It also indicates that you can open and close your garage door as many times as you want in a day. Your garage door will remain functional and reliable throughout its product life. Do you need a new garage door spring in Pittsburgh? Contact A1 Garage Door Pittsburgh for a friendly and affordable spring garage door repair. Our technicians have been replacing garage door springs for many years now. Our clients in the area can attest to the quality of all our garage door solutions. Call us today to find out our rates and services.

Rate this post